Welcome to FPVDronePilots!
Join our free FPV drone community today!
Sign up

Recent content by REX

  1. REX

    wire XM+ and bind with X9 lite

    Hello Yes, all is working....funny thing is that if they are within 1 meter distance, I will lose signal. .o_O The only small issue is that when I was outside, the trashcan behaves weird sometimes (not always), like if the wind will hit it. If this happens again, I will try to make a...
  2. REX

    wire XM+ and bind with X9 lite

    Quick update here. I went outside and the receiver and vtx signal seem to work correctly. hmmm :0 in any case thanks a lot.
  3. REX

    wire XM+ and bind with X9 lite

    you are right!!! if I am 2 meters away, it will work!!! However, I have issues with my fatshark googles. it shows RSSI 100% and after 2 minutes it goes down to 10% Moreover, I have no values in the taranis.
  4. REX

    wire XM+ and bind with X9 lite

    Hi again I have tried to bind it, but I had no success. I upgraded the firmware in the receiver. I used the file named: XM_ACCST_2.1.2_FCC.frk after that, I soldered it to the quad. see pics below However, there was an issue. For some minutes the green light was solid. After that red...
  5. REX

    wire XM+ and bind with X9 lite

    Hi Thanks a lot for your reply: In theory, I should be able to bind the receiver using the following instructions: Registration & Automatic binding (Smart Match ) With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "F/S" button. Follow...
  6. REX

    wire XM+ and bind with X9 lite

    Hi all I could say I am new to the hobby, but I have been reading some posts and watching several youtube videos I have the trashcan and the x9 lite (ACCESS) As receiver, I would like to use a XM+. I've seen that flashing the reciever is recommended it, but I could not find the firmware...
  7. REX

    Frsky Access and R9 modules

    Regarding R9mm and ACCESS In order to bind R9MM receivers with taranis X7 Q, you must always flash the receiver ??
  8. REX

    Totally New

    Thanks again! its exactly like you write above. I'll try to bind it during the weekend. I'll follow on your suggestions. Thanks
  9. REX

    Totally New

    Hello Pauper Thanks for your reply. It was bounded with taranis x9 lite, then I guess, the receiver should be Frsky LBT thanks
  10. REX

    Totally New

    Thanks a lot for your reply. I have other quads bound to the radio. I would prefer to flash the receiver. I have one question, how can I know which receiver does the meteor65 has? thanks
  11. REX

    Totally New

    hello It says Access...
  12. REX

    Totally New

    hello all How could actually bind the meteor65 to Taranis X7 FCC version? Thanks
  13. REX

    Larva X buzzer

    Thanks, it works. The only thing is that is not very loud, would the buzzer be much louder? does it worth installing it? Thanks for your comments
  14. REX

    Larva X buzzer

    Hello Guys I am having issues to enable the beeper in my larva X (Crazybee F4 Pro V3 Flight Controller) I am not sure if I can use the beeper mode in the larva X and I need to install a buzzer instead First question: For the larva X, Is it possible to enable the beeper in betaflight...
  15. REX

    how to know batteries are fulled when Parallel Charging

    Hello all I can not charge a 3s lipo battery. The charger says "error connect" It seems some cells are dead. I check the battery and these are the readers: 1s: 0.00 2s 4.133 V 3s 4.190 V How can know if a cell is dead? is perhaps only the cable? Thanks