Welcome to FPVDronePilots!
Join our free FPV drone community today!
Sign up

receiver

  1. S

    Fpv drone bound to radio but doesn’t fly or show up in betaflight

    I’m new into fpv and I bought the mobula7 with elrs version but since I have a radiomaster boxer 4in1 protocol so I bought a RadioMaster - R81 2.4GHz 8ch Frsky D8 Nano RX and bound it to to radio it says telemetry recovered but it doesn’t fly or show up in betaflight. It was a sbus so I soldered...
  2. J

    New to FPV, can't set up my drone

    Hi everyone, So... I've built and flown RC planes very on and off since I was a kid and recently decided to give FPV drones a try having had a great time flying some planes fpv. I have bought a darwinfpv baby ape, have soldered on (maybe wrong) a flysky fs-a8s receiver and have spent hours...
  3. E

    can we change UART number for SBUS tx receiver?

    "can we change UART number for SBUS tx receiver(futaba)? "Hi, I recently bought AIO, and trying to do soldering a receiver on AIO pad. Problem is GND pad is really bad, and a wire always come out easily. Then I am thinking to do soldering for the receiver on R4 GND 5v pads where pad conditions...
  4. Reddley

    I need help finding receivers for Taranis QX7

    I'm looking for a reciver with 6ch or more for use in my rc cars and lego projects that can bind to my Taranis qx7. The kind I'm looking for are XM+ I believe. This is what one I need looks like. Thank you.
  5. Z

    Problem Binding the Mobula 7 to QX7

    I have been struggling to get my quad into the air and think that here might be a good place to get some advice. I recently received the Mobula 7 quad. It has the XM+ receiver module which I believe uses the EU LBT firmware. I therefore flashed the this firmware onto the OS of the QX7 (it...
  6. K

    Problem: Mobula7 not binding to radio, Taranis QX7

    I recently bought a Happymodel Mobula7 from banggood. It's "bind and fly" however, out of the box It struggled with the whole binding part. I have a taranis QX7 for a radio. I'm fairly new to the hobby so I was wondering if anyone here had some advice. Everything else seems to work fine I'm...
  7. FrankV01

    Antenna Pulled off FrSky XM+ Receiver

    I just noticed that one of the two Antennas had been ripped off the receiver. How might I re-attach it? Can I solder it or should I replace the receiver? Mind you, it's only $13 so replacement is fine if that is better.
  8. H

    Receiver Mounting

    I"m using a FrSky R-XSR Receiver, but I think my question applies to most receivers.. what's the best way to attach the receiver to the frame? I"m currently using double sided foam tape, but that doesn't seem to do a very good job, and the receiver ends up being held on by the antennae that are...
  9. O

    Can't wire Turnigy receiver to flight controller

    Hi, I'm a total beginner to fpv quads and I've purchased a Spedix 250 Pro BNF just to get a taste of fpv. I have a Turnigy Evolution as well, but I cannot figure out how to wire up the TGY-ia6C receiver to the flight controller so I can bind it. The quad came with a 10 pin plug which I've...
  10. bmw546

    I accidentally cut my ar610

    i cut the long cable of my receiver specktrum ar610. (Like in the first 1/3 of the cable)
  11. Jack Ley

    New Quad, Connecting to Baseflite

    I just got an ARF Anakin Sky-Hero the other day, it just needed a RC, which I have, battery and receiver. After some frustration I finally got the receiver hooked up,(this is my first non RTF quad, so this all new to be) I bound the receiver to the my AT9 RC and then I wanted to connect to...
  12. D

    DJI Compatible Receivers

    Hello drone builders, I am about to start building my own drone for racing and have a spare DJI Phantom3 RC that I was hoping to use. However, I have been struggling to find a DJI receiver at a reasonable price (don't fancy paying $300 for a P3 main board). Can anyone advise/recommend a DJI...